Monthly archives for December, 2014

Make A Copy of Key With 4D Cloning To...

If you plug 4D CLONING TOOL device in USB port first time operation system offer to install the driver of located device. Choose the manual installation method withpoint of driver directory (it is 2nd method). Point the directory to folder “FTDI/driver/” from CD. If you have done everything correctly,then the operation system will confirm tha [...]

Use the Galletto 1260 tool to read/wr...

Below are some brief instructions to follow when using the Galletto 1260 tool to read/write your ECU. How to read the ECU: 1. Prior to connecting the Galletto 1260 you must copy the software from the mini disc and add it to the desktop on your laptop. If you don’t have the disc the software is available on the HDI-Tuning website. 2. To [...]

How Does AK500 PRO Key Programmer Sel...

Mercedes Benz KELESS GO Contains Two Styles: Old Style with Black Edge and New Style with Electroplating Edge 1, When use new style key with electroplating edge to process KEYLESS GO, if original key is with black edge, then keyless go key must be with black edge( the key must be fully-new blank or has been refreshed to blank, and remote cont [...]

How To Reset The Airbag Light?

1. Turn ignition switch off, remove ECU service connector 2. Connect (jump) the MES connector (this is 2 pin yellow connector wrapped in yellow plugged in the front of the underdash fuse box) 3. Turn ignition switch on 4. SRS light will come on for 6 secs then go out, remove the jumper within 4 secs after the light goes out. 5. The SRS light [...]

MB Star C3 Software Installation

How to install the MB Star C3 software? If you bought the MB Star C3 super software with external HDD,that’s good,it can be used on ordinary computers. But how to install the MB Star C3 software ?Your mb star c3 need to code calculat. MB Star C3 code calculating: I will send you new STARTKEY. Please delete the old StartKey, and put [...]

Multi Di@g Access J2534 VCI Serial Nu...

Multi Di@g Access J2534 VCI Serial Number During installation, when Multi-Di@g configuration window appears, you should set Communication interface to USB and set VCI serial number to A070026: After installation, MultiDiag shows message asking to get activation code: Press green button and you will see window asking for code. Please contac [...]

Launch X431 Diagun III X-431 Bluetoot...

1. Install battery Install steps are described as below: 1. Follow Fig.a to push the button cabinet forward to open position, and then remove it. 2. Take out the battery form the package box and install it as indicated on Fg.b. 3.Cover the reader cabinet and push it backwards to the original position, as shown on Fig.c. To disassemble the bat [...]

OBD-II ELM327 WiFi Interface Quick Se...

Interface Setup Setup of the OBD-II ELM327 WiFi Interface is quick and easy an in just a few steps you will be connected and receiving information from you vehicle. Troubleshooting and suggestion bullet points are included in this setup guide but are included only as a point of reference to help you get connected and monitoring your vehicles [...]

VAG KM+IMMO TOOL Process of adding de...

1. Condition 1: At least one key can be used. 1) Connect “VAG KM+IMMO TOOL” to both PC and car. 2) Click “EEPROM” button, read EEPROM and save it for backup. 3) Click “Dealer  Key” button ,opel “Dealer key” Dialog. 4) Use the prompt key chip to make key. NEC24C32 and NEC24C64; Megamos 48 CDC VW: [...]

Fly100 Honda Software Set Up Installa...

Usually, you fail to setup FLY100, because you do not successfully install Patch or USB Driver. Patch installation process Three steps about Patch installation process are listed as follows: Step 1: Open “Patch” Folder, and then double click “FLY100 Patch Process .exe”. Step 2: left click “Operation” button. Step 3: click “close” button, when [...]