Posts in category Car Diagnostic Tool

How To Use ADD7703 Brake Liquid Quick...

1. After cleaning the probe, put it in dry air or immerse it into new brake fluid. 2.Press down the work button for 3-5 seconds continously, and then turn the fine tuning clockwise until the second green indicator lights on, and then turn the fine tuning counter-clockwisely until the green indicator put out. Now it can be used to test brake f [...]

How to Use 2015 FVDI Software USB Don...

How to use the FVDI software USB dongle: 1)Ensure there is good network connection environment 2)Run “ABRITES Quick start”. Select quick link icon on desktop and open “ABRITES quick”. Then select vehicle icon, software is running when the Dongle icon on the right-bottom of the desktop pops out. 3)Plug the software dongle into the computer/lap [...]

How to use Ford Outcode / Incode calc...

How to use Ford Outcode / Incode calculator? When you place an order from us, we ship you a WS Dongle(USB Key), at the same time, we send you a software driver . After receiving the WS Dongle(USB Key, you connect WS Dongle(USB Key) with your computer USB com port and then run the software driver, once finish setup, it’s ready to calculate the [...]

Use the GM Mini MDI in combination wi...

MAXIMIZE SERVICE SPEED AND REVENUES WITH A COMPLEMENTARY TOOL STRATEGY To help you get the best return for your tool investment and maximize your revenues by servicing more vehicles in less time, we want to make sure you understand how and when to use the new GM multiple diagnostic Interface (MDI) in combination with your gm tech 2. First, a [...]

How to Use VOLVO Serial Cable ?

-For laptops and PCs, download the shareware 1.3  -Run it and follow the prompts to allow it to install itself. Note: You must install volvo FCR on your PC`s hard disk — it will not work properly if you try running it directly from a floppy or CD. However, you can use a floppy or CD to move the distribution file from a PC with internet [...]

OP-COM Driver installation And Softwa...

OP-COM Driver installation And Software Activation 1. Firstly put the small CD that came with the package into the CD drive. Do not plug the device. 2. Copy the folder and its contents to a suitable location on your PC, the desktop is fine. 3. Now open the folder you copied, here you will see 2 yellow icons Op-Com.exe and activate password .e [...]

How To Reset The Airbag Light?

1. Turn ignition switch off, remove ECU service connector 2. Connect (jump) the MES connector (this is 2 pin yellow connector wrapped in yellow plugged in the front of the underdash fuse box) 3. Turn ignition switch on 4. SRS light will come on for 6 secs then go out, remove the jumper within 4 secs after the light goes out. 5. The SRS light [...]

MB Star C3 Software Installation

How to install the MB Star C3 software? If you bought the MB Star C3 super software with external HDD,that’s good,it can be used on ordinary computers. But how to install the MB Star C3 software ?Your mb star c3 need to code calculat. MB Star C3 code calculating: I will send you new STARTKEY. Please delete the old StartKey, and put [...]

Multi Di@g Access J2534 VCI Serial Nu...

Multi Di@g Access J2534 VCI Serial Number During installation, when Multi-Di@g configuration window appears, you should set Communication interface to USB and set VCI serial number to A070026: After installation, MultiDiag shows message asking to get activation code: Press green button and you will see window asking for code. Please contac [...]

OBD-II ELM327 WiFi Interface Quick Se...

Interface Setup Setup of the OBD-II ELM327 WiFi Interface is quick and easy an in just a few steps you will be connected and receiving information from you vehicle. Troubleshooting and suggestion bullet points are included in this setup guide but are included only as a point of reference to help you get connected and monitoring your vehicles [...]